Tuesday, August 19, 2014

FREE Tutorial: Jumbo Rosette Bracelet

Making linked wire “rosettes” with intertwined jump rings is nothing new. But have you considered making big, jumbo-sized jump rings using 12-gauge wire? Once you cluster and link your chunky rings together with doubled figure-8 links, you’ll have a beautifully bold jewelry piece that’s sure to attract notice. Best of all, this bracelet is easy to make in an afternoon. The design can also be used to make chokers and longer necklaces, too.
Wire flush-cutters suitable for cutting up to 12-gauge wire
Ruler and/or measuring tape
Hard-plastic or rawhide mallet
Chasing hammer or planishing hammer
Small bench block
12-gauge round copper wire: about four to five feet (possibly more, depending on the length of your bracelet, or if you use this design to make a necklace instead)

Step 1: Working off a spool of 12-gauge wire, flush-cut the end:
Step 2: Measure and flush-cut several 2-1/2-inch lengths of wire, ensuring that each wire length is cut flush on both ends. I cut nine of these lengths for my bracelet, but you may need more or less depending on how long your bracelet is or if you use this design to make a necklace or choker:
Step 3: Place one wire piece in the jumbo tapered round mandrel pliers about one-third of the way from the tips of the tool. Tip: You can see that I marked my tool with a Sharpie pen to help me make every loop the same size:
Step 4: Bend the wire all the way around until it touches itself. Flip the link over and repeat, which will shape a large figure-8 link:
Step 5: If the link is a bit misshapen, place it on a steel bench block and hammer it firmly using either a hard-plastic mallet (shown) or a rawhide mallet:
Step 6: As an alternative to the previous step, you can straighten out your link by squeezing it firmly in the chain-nose pliers:
Step 7: Make several figure-8 links (as many as needed for your particular project), and set them aside:
Step 8: Again working off the spool of 12-gauge wire, form loops of wire on the very back of the jumbo tapered round mandrel pliers as shown. Make sure that each loop is made in the same place on the tool, so that every link will be identical in size and shape:
Step 9: Flush-cut the wire end using quality flush cutters suitable for 12-gauge wire:
Step 10: Use the cutter to pull the next ring slightly apart from the coil you made earlier, and flush-cut off a ring:
Step 11: Make a big pile of these jumbo-sized jump rings. I used 25 rings in the finished bracelet pictured:
Step 12: To “condition” your jump rings, pick them up individually and wiggle the ends together until they meet perfectly. If one wire end pokes up a bit above the other, use the tips of the chain-nose pliers to bend the wire end down until the jump ring is perfectly round with ends that meet flush:
Step 13: To further condition and work-harden your rings—which is especially important with big, jumbo-sized rings like these—hammer them firmly with a hard-plastic or rawhide mallet:
Step 14: Make a big pile of rings! At least 25.
Step 15: Pick up a ring and open it up sideways using chain-nose pliers. Insert one end into another, closed ring:
Step 16: Wiggle the two ends together as in step 12 to close the second ring firmly. Place the two rings on your work surface as shown:
Step 17: Repeat steps 15-16, this time inserting the wire end into the two previously linked rings:
Step 18: Close the third ring (as in step 16):
Step 19: Pick up a fourth ring, open it sideways, and insert one end into the three linked jump rings:
Step 20: Close the fourth ring as before, and place the linked rings on your work surface as shown:
Step 21: Pick up a fifth ring and, as before, open it sideways in order to insert one end through the four previously linked rings:
Step 22: Close the fifth ring firmly and place the linked rings on your work surface. Repeat these steps until you have five sets of five jump rings, intertwined and linked in the rosette pattern:
Step 23: Pick up one of the large figure-8 links you made previously, and open up one loop sideways in the chain-nose pliers:
Step 24: Run the wire end through a rosette cluster and close the loop sideways, ensuring that the wire end meets itself firmly as shown:
Step 25: Repeat this step until you have placed four figure-8 links onto a rosette cluster. Separate the figure-8 links as shown, with doubled sets on each side of a cluster:
Step 26: Repeat steps 23-25 with a second rosette cluster. You should begin to see the pattern emerging:
Step 27: Repeat steps 23-25 again. You now have three rosette clusters joined together with doubled figure-8 links. Continue in this fashion until you have connected all five rosette clusters with doubled figure-8 links:
Step 28: To make a hook for your bracelet, flush-cut about 5-1/2 to 6 inches of 12-gauge wire. This measurement doesn’t have to be exact:
Step 29: Use large flat-nose pliers to fold this wire at the halfway point:
Step 30: Bend up the bent wire end using the tips of the jumbo tapered round mandrel pliers:
Step 31: Use large round bail making pliers to bend the wire up and over, forming a hook:
Step 32: Optional: Hammer to two wire ends on the hook using a chasing or planishing hammer. The idea is to slightly flatten the wire ends, making them easier to bend in the next step:
Step 33: Place the two wire ends in the large round bail making pliers and bend the wire around until it touches itself:
Step 34: To place the hook on one end of the bracelet, open the two loops (made in step 33) sideways, run the opened wire ends through a rosette cluster, and close the loops sideways:
Step 35: Here is how the bracelet looks so far. If it’s long enough at this point, it’s finished (lacking a good polish, of course!). However, if you would like to lengthen it a bit, continue:
Step 36: Flush-cut a piece of 12-gauge wire approximately 2-1/2 inches in length and form it into a figure-8 link (as described in steps 2-6):
Step 37: Grasp the link with chain-nose and flat-nose pliers and twist firmly so that each loop on the figure-8 is at a perpendicular angle to the other:
Step 38: Open up one loop sideways and place it on a rosette cluster:
Step 39: Here’s how the finished bracelet looks on! Super big and chunky, and yet surprisingly comfortable to wear with a lovely drape around the wrist. Yummy!
Option: The finished bracelet as pictured was darkened with a hot solution of liver of sulfur, and then polished with 0000 steel wool from the hardware store. Instructions for this process are provided on my DVDs and in my books and ebooks.
I hope you enjoyed this free tutorial! I share lots of wire and metal designs in my various books, ebooks, and DVDs filmed in closeup detail. I hope you'll check 'em out!
Happy wrapping,


Terri said...
This comment has been removed by a blog administrator.
Ammu said...
This comment has been removed by a blog administrator.